Search results

Ok , the Ex was in a fender bender, and I just had it repaired. Now if it sits over night, the battery goes dead. Already replaced the battery, and Alt, and am getting almost 16 volts at the battery when she runs. Is there a way I can check with the Volt/Ohm meter if there is a drain due to a...

Say a guy had a donor BroncoII with a Mitsi 5 speed manuel, could this be swapped into a 95 Ex Sport , with a auto. ?? I mean the whole kit, manuel trasfer case and all?? I have one, and a O/D Off light flashing again an the Ex.

Just got approoved. Here's a pic of the truckhttp://www.mudnuts.org/gallery/dalton04_tnt/aav 3" body lift, TT and shackles, 33x12.5x15 Wide Climbers, hypertech chip, cold air intake, flowmaster cat back exhuast., No-slip up front, lock-rite in the rear.

Who says they can go anywhere?? I was just in that hole 15 minuets before. This was at a Mudnuts event here in New York last weekend.http://www.mudnuts.org/gallery/dalton04_brian/abf Here's the Ex. Wainting to run the Hard trail. http://www.mudnuts.org/gallery/dalton04_brian/aaf

Can someone give me the axel codes for the Bronco II?? I just aquired a free one in pretty good shape. Also, where do you guys find these?? Is there a site to go to?? Thanks;)

My buddie was wanting to lock the front and rear of his 97 f150. What are the axels he has?? I always thought the trucks came with 9" rears , but his has a cover, and I was thinking that the Ford 9" had no cover, just a 3rd member. His front obviosly is IFS. Thanks;)

Ok, pulled into work tonight, went to back into my spot, and she won't go?? Get out, take a look, nothing, went to back up again, goes into gear, still won't go. So a buddy comes and takes a look, I gas her, and the front right(passenger side) is locked up. Only in reverse though. What can it...

I was wheeling last week, and hit a cut off tree pretty hard with the right front tire. Bad enough that I ruined a upper Ball joint and bent the spindle ( knuckle). Well , the ball joint is replaced, and the I got a used spindle, now the only thing that isn't working is the power steering. No...

I was wheeling last week, and hit a cut off tree pretty hard with the right front tire. Bad enough that I ruined a upper Ball joint and bent the spindle ( knuckle). Well , the ball joint is replaced, and the I got a used spindle, now the only thing that isn't working is the power steering. No...

Was out wheelin , and was coming out of a mud hole, and back out on the trail. Didn't see the tree that had been cut off, and left on the side of the trail. Well I whacked it with the Right front tire, bending the upper ball joint, and the spindle( Knuckle) . In the process of putting it back...

Anyone know where in the Haynes Manuel it covers the replacement of the front axel seals, passenger side?? I can't find it. If it isn't there, can anyone help me out??

Sorry , I have no digital camra. Over top the spare in the back, between the frame rails , is a black box, with two rubber hoses. What is it?? I was thinkin maybe for gas vapors?? I really have no clues.

Let me set the stage..... Way back in Sept., I ordered the flowmaster Exhaust, and front and rear No-Slip Lockers for the Ex. Well the exhaust came , then in Dec. the front locker came, but I have since waited for the rear Locker. And I have called them and TruckPerformance each month and...

Ok , I know it is just an idiot guage, but mine always reads at the max, once in a blue moon , on a long drive it will come down into the normal range. My guestion is.... when I turn my engine off, and put the keys in my pocket, it stays at the top. Is it suppose to come down to the bottom like...

When I installed my front locker, the directions stated that the ring gear should not cover the pin, unless the gearing was lower ( numerically higher ) , well it did cover the pin!! Upon further tearing appart to get the ring gear off, I noticed that the ring and pinion har white grease marker...

Well it's done. Not as easy as they make it sound. First on the 95 + Ex's you have to remove the hole front axel from the truck. Took me bout an hour. Then the fun stuff. Soon as I get the cover off, I see someone has regeared my Ex, I no longer have 3:77's. Not sure what I have now, but the...

I went to the Carquest auto parts store to pick up some Syn Gear oil, and asked about a in line tranny filter, he said he could get one the next day to me , so I ordered it. Well I picked it up, and it was a magnafine filter!! The good part is I got it for only 12 bucks!! I see on the Magnafine...

Ok all I want is a 3-4 inch lift for a 95 sport. I can get them for 91-94 9 (twin I Beam) and 96- current (IFS). Now the 95 is IFS, whats the difference in the 95's that make them the ******* children with lift Companys??:eek:

I have had my front locker for a month now, and if anyone knows, getting to the front Diff cover is a PITA. Well for giggles, I thought I would stop into my Mechanics shop and just see how much he would Rape me to drop the whole axel and install it!! He says, bring it 3 s Saturdays from now...

Well I have to set the situation up a little. Momma been bustin my chops, about my truck. 4x4 is over rated, you don't need all the parts...... my front wheel drive go anywhere in the snow etc. , You get the picture. Well we got 12+ inches of snow the other night. And then the plows come...

I went to install my Powertrax No-Slip Locker in the front Differenial. Well , I guess I didn't realize I had to remove the entire Axel to get to the diff. cover!! We idn't have enough time , or the two jaw pullers need to do this. So we gave up. So now I guess I better schedual a whole weekend...

All I want is a 2.5 to 3" body lift for my 95 Ex Sport. All I want is a Web site or a part number. Please.... pullin all my grey hair out here.:rolleyes: PS... I did the Shackle drop and TT already...thanks

Fiberglass After market Parts?? Well I tried this over in the Body and Detailing forum, just aint no traffic there. Maybe some one here can help.I am looking for a fiberglass rear Lift gate for my 95 Explorer Sport. Are they out there?? I know they make fenders , but I will be needing a lift...

I am looking for a fiberglass rear Lift gate for my 95 Explorer Sport. Are they out there?? I know they make fenders , but I will be needing a lift gate. Please help!

I just gotta get this of my chest. I come here everyday, and see time after time. "Do a search to find what ya need!" I moderate a Duckhunting site, and we never treat prople this way, or for that matter, any other site I see. There are such things as new people, or people not knowing a Mod or...