Search results

http://www.dfw-tx4wd.org/ March 6,7,8

Does anyone make a Heim joint that will thread onto the end of a D44 radius arms? If not, has anyone engineered something like this and has pictures of the work? Thanks. Rob

I've searched "Doubler" and "Stubler" and it looks like DD Machine and T&M are the only producers of an adapter for a DIY doubler. It looks like at one time DD had a problem delivering. Has that improved? Does anyone else make an adapter kit? Thanks. Rob

They ready have earned respect on the trails, but now they should have a better forward bite. Here are some pics to compare. The tire on the right is grooved, the one on the left is not. Rob

I'll be there today. Look for my maroon/grey 4door if anyone else can make it. Rob

I'm wanting to relocate my air filter to the driver side but need to extend the wires to the MAS. Will extending these wires cause a problem for the computer or sensor readings? If anyone else has done this, please chim in. Thanks.

I've seen a few rigs here with a SAS using a steering setup similar to the OEM style and would like to re-engineer my steering likewise but can't seem to overcome a couple big problems. First of all the OEM tie rod and drag link are now long enough so the adjusting sleeve needs to be adjusted...

I need some help finding coil springs for my front end. When I fabricated the front axle brackets and mounts for my SAS, I reused the OEM upper and lower '91 Explorer coil spring mounts and cut down a pair of Superlift 5.5" lift coil springs to achieve the desired height. Of course we all know...

I'm contemplating Hydralic Assist on my '91 with a HP D44. Who has done this that can shed some light on what is needed to make it work? FWIW, my other option would be a flat top knuckle and high steer arm.

I tried to research this problem but wasn't able to find anything similar to may help. This is the history...I swapped out the auto transmission from my '94 Explorer for a 5 speed and swapped transmission harnesses, but left the original ECM in it. I wouldn't bet me life on it, but I'm...

I am going to recover my headliner but before I begin removing it I wanted to find out if anyone can share tips to get it out. Thanks

I'd like to find some female heim joints that will screw onto the ends of the radius arm so I can do away with the bushings. My front end consists of a '78 F150 SAS with the '78 F150 radius arms. I found some female heim joints with 3/4 x 16 threads on-line. Does anyone know these will thread...

how many amps does a '91 alternator put out? I'm wondering how the charging system will be affected if I replace the clutch fan with a Taurus 2 speed fan.

This is for those of you with body lifts in the warner part of the country... Do you have cooling problems because of the gap created when the fan shroud is dropped?

who sells a steering arm to mount atop the right side D44 flat top knuckle?

I'm have some serious cooling issues on the trails and am considering removing the clutch fan and installing a 2 speed electric fan from a Lincoln/Taurus. How well does that fan fit on the 4.0 SOHV radiator? Is there a better one to use? Are there any drawbacks? Thanks

The fuel gauge in my '94 X is not registering. How can I determine if the problem is in the gauge or with the sending unit? And yes there is gas in the tank. :)

I'm thinking about converting my '91 X to use an electric transfer case but I don't have the wiring in mine. I've got a donor X and can see that the transfer case wires go through the floor under the driver seat then follows another harness along the floor on the left side and heads toward the...

I just completed a manual to auto trans swap including a new/used ECM for a '91 with an Auto Trans. Now I'm getting this code, along with a couple others. Prior to the swap, I wasn't getting any codes. Code 22 is: MAP (vacuum) or BARO signal out of range - MAP. What is this telling me and...

I just completed swapping in a '94 A4LD for the M5OD in my '91 Explorer and now I'm getting code 67 (Park/Neutral circuit fault - PNP , Transmission Manual Lever Position (MLP) sensor circuit - Transmissions ) and Code 89 (A4LD - Converter Clutch Override solenoid - Transmissions ). What are...

will the front and rear seats from a '95 model fit in a '94?

Mark gave me a smoking deal on a ECM. It was packed great and shipped on time. Great communication and very dependable. He did exactly what he said he was going to do.

I couldn't find any search results explaining this, but is it similar to Chevrolet where you push the cable in then push the gas pedal to the floor to let it "rachet" out. thanks.

According to my search results and the dipstick, this transmission uses Mercon, not Mercon V or Dextron Mercon but I can't find just the Mercon fluid. Help please.

This is really for anyone who can help. I'm installing the Transgo A4LD Junior kit in a '94 A4LD but have hit a wall. I'm shooting for "Firm" but can't find drill bits for these hole: .076, .125, .053-.055, or .080-089. Glacier, I noticed you had a nice selection of bits labeled this...