Search results

Mice chewed the insulation off my throttle cable. Throttle sticks sometimes so i keep spraying it. It's kinda dangerous so I would like to replace the cable. I'm not seeing anything available. Would anyone have the part# for the throttle cable? Or are there aftermarket cables that aren't too...

Hello, Is the muffler for the 94 XLT 4WD an offset in, center out? Thanks. Also the rear steel brake line passenger side is leaking at the junction block above the pumpkin. Does anyone know the brake fitting size/pitch? I can make the line but the fittings are not in great shape. And is it a...

I am in need of both front fenders for my 94 4WD XLT. Any sources for new parts? Thanks in advance.

So I am starting a new thread on this subject, continued from a previous thread. I have been hearing a slight hiss under the dash since I got the truck, but everything seemed to be working ok so I never really thought about it. I recently cleaned out my heater box, and did some heat-related...

Hello, I have been searching the threads here, and I think I might need to ask a question- I replaced radiator, water pump, heads, new rad hoses a year or two ago. Also installed a new stant thermostat, new temp sensors. Temp gauge always read low after this, but the heat was still hot. Noticed...

Hello, I need to replace all of my steering linkage, 1994 4dr XLT 4wd ordered parts before realizing that the 2wd and 4wd steering linkages are different. the 2wd center link and inner drivers tie rod are bigger in diameter, seems like 1” the 4wd center link and inner drivers tie rod are...

I have a 94 XLT and I will be removing the front seats to install some audio stuff. My cargo area and back seat area carpet is actually in really good shape. But the front seat carpet is kinda crappy Looking to replace my carpet, it is grey in color Not sure which part of the VIN gives the...

Hello, whenever I unlock the pass front door, whether by using the buttons on the door or with a key, the button will fall and the door will lock. Almost like it is falling with gravity. I recently replaced both rear latches, and surprisingly the front drivers side is fine. is there a spring...

Hello, I am pretty much a car audio noob, but have experience with electrical and wiring. I recently replaced the 4 door speakers with 65watt rms 3 way speakers. They are 4ohms Would like to add a 2x12 kicker box with subs for the back. I will obviously need to get an amp and a new single din...

Hello, I busted my RDS door lock actuator replacing the latch. It looks like the actuator is riveted in? How do I go about removing it, and where would I find a new actuator? Thanks in advance for any info. Also the plastic piece that has the threads for the rod that goes to the lock/unlock...

Hello, I need to replace all 4 door latches in my ‘94 Are the front and rear latches the same? Or are they different because of the child locks in the rear? Thanks for any info I really appreciate it

Hello, I am in need of some help, I am baffled by this but I know someone will be able to get me on the right track. I had been having an intermittent problem with the truck not starting after being shut off. Fuel pump would not prime. I would remove the relay and put it back, wiggle some...

i just removed my headliner due to it being badly trashed when I bought it. Plus I am leaking water at the drivers rearmost window, had to remove to see if it was the window or the roof racks. At this time it appears to be the window that is leaking. The carpet pad was pretty damp, I took it...

Hello, I have a 94 XLT I have (2) heated mirrors which I have installed and wired up the drivers side. On the passenger side, I would like to remove the stock convex glass(objects in mirror are closer than they appear) and replace it with regular flat mirror. I have a CDL and have gotten used...

Hello, I have a door panel that is driving me nuts and it’s broken at the top where the switch panel sits. A new handle will not fix it. Only a new panel will. I have done a ton of work already as the handle came off in my hand a few years ago. If I can just glue that break I think i’ll be...

Hello, I bought some OEM heated mirrors for my 94. It did not have heated mirrors from the factory. I did some searching on here and seems that the consensus is that the rear window defroster switch provides timed power to the mirrors. In looking at my wiring diagram, it appears that there...

Hello, Feel like it’s one step forward 2 steps back with this truck sometimes. Haha I recently replaced P/S pump, steering gear and lines in my 94. Lines new, pump and steering gear are reman. My front axle shaft u joints were seizing up slowly over time, so that the P/S system was working way...

Hello, I am looking for good used 3.27 ring and pinion gear set for front TTB Dana 35, in a 1994 Explorer. I think they are reverse cut gears? Let me know what you have, I cannot find 3.27 in new gears it seems it is not a popular size so hopefully that means there are lots that have been...

Hello, I am having some rear spring work done on my truck. While it is there i wanted to have them replace the front pinion seal. The shop is saying you have to drop the pumkin to replace it. Is this true? I feel like it can be done without dropping it again but figured i’d ask here Thanks!

Hello, In the process of drilling out the bolts on the ABS sensor bolts, I messed up the little mounting tube on the spindle with angle grinder. I think it might be ok if I build it back up with some TIG welding. Is this piece removable and available separately? Knuckle on right is OK it...

Hello, I am looking for any RA bushing recommendations or brands to avoid etc would be great! Thank you!

Hello, I will be replacing ball joints, spindle bearings and u-joints in the front of my 94 4x4. I ordered the joints and the spindle bearings, but does anyone have a part number for the u-joints? Thanks in advance

Hello, My 1994 4x4 is having steering problems. I jacked it up on each side and found pass side rotor slightly loose. Removed keeper tightened nut, no more loose. Drivers side seemed dry, I think that bearing might be bad. I repacked it just because I would need it to get to the store to get...

Has anyone ordered lifters from this company? Set of 12 LIF422 Lifters DNJ Was just wondering if they are any good, any fittment issues? It also doesn’t say whether they are new or reman?

So I installed new pushrods on Monday. Some of the old ones some had worn footballed ends. I had some annoying top end chatter and thought I had a bent pushrod. One pushrod was def worn/slightly bent but most of them were straight. The new pushrods helped the noise quite a bit but it is still...